Deprecation: Enabling Unified Mode (CHEF-33)

Unified Mode (unified_mode true) is the default behavior starting in Chef Infra Client 18 (April 2022).

See the following table for Chef Infra Client versions where Unified Mode can be enabled in custom resources:

Unified Mode is enabled by default starting in Chef Infra Client 18.

In Chef Infra Client 17 (April 2021) and some earlier versions, you can enable Unified Mode in custom resources by adding unified_mode true. You can upgrade most custom resources to use Unified Mode without additional work other than testing and validation. See the following example:

# enable unified mode
unified_mode true

provides :myresource

actions :run do
  [...]
end

Actions on Later Resources

Since Unified Mode executes your resource as it’s compiled, :immediate notifications that execute later resources are handled differently than in the past.

:immediate Notifications to Later Resources

Unified mode delays immediate notifications to later resources. In unified mode, the Chef Infra Client saves immediate notifications and executes them when the later resource is parsed. Immediate notifications to prior resources and delayed notifications behave the same as they did before unified mode.

The result of sequentially chaining immediate notifications is the same as before unified mode. Instead of immediately notifying results, the notifications fire in order as they’re parsed, which has the same outcome. If the parse order and the intended execution order are different, then the results may be different and are a reflection of the parse order.

The changes to sending immediate notification could result in subtle changes to behaviors in some resources, but it’s not a breaking change to common patterns of writing resources.

Chaining immediate notifications to later resources:

remote_file "#{Chef::Config[:file_cache_path]}/myservice.tgz" do
  source "http://acme.com/myservice.tgz"
  notifies :extract, "archive_file[myservice.tgz]", :immediately
end

archive_file "#{Chef::Config[:file_cache_path]}/myservice.tgz" do
  destination '/srv/myservice'
  notifies :start, "service[myservice]", :immediately
  action :nothing
end

service "myservice" do
  action :nothing
end

:before Notifications to Later Resources

In unified mode, you must declare a resource before sending a before notification to it.

Resources that subscribe to a before notification to a later resource must be declared after the resource that triggers the notification.

This resource declares a before notification to a later resource and will no longer work:

package "myservice" do
  notifies :stop, "service[myservice]", :before
  notifies :start, "service[myservice]", :immediately
end

service "myservice" do
  action :nothing
end

Instead, declare the resource and then declare actions. For example:

service "myservice" do
  action :nothing
end

package "myservice" do
  notifies :stop, "service[myservice]", :before
  notifies :start, "service[myservice]", :immediately
end

Out of Order Execution

Unified mode breaks custom resources that rely on the out-of-order execution of compile-time statements. Move any affected compile-time statements to the location in the code where they’re intended to execute.

Out-of-order execution is rare. Internally at Chef, none of our custom resources broke during our migration to unified mode. Instead, we discovered a few cases in which custom resource code was intended to run in order, but Chef Infra Client executed it out of order. In these cases, Unified Mode fixed errors instead of introducing bugs.

Troubleshooting Unified Mode

Unified mode changes the execution of a custom resource to run in one phase, in the order that the code is written, from the first line of the code to the last. Custom resources designed to use two phases may need modification. These fall into three general types:

• Resources with changes to internal sub-resources
• Resources with actions on later resources
• Resources that rely on the out-of-order execution

When designing a custom resource for unified mode:

• Declare a resource first and then declare actions on it
• Write resources in run-time order

Resources with changes to internal sub-resources

Some custom resources are designed to create and edit other sub-resources as part of the resource declaration. In unified mode, Chef Infra Client parses a resource code block that creates or edits a sub-resource and immediately tries to apply that change, even though the sub-resource doesn’t yet exist. This results in the execution of an incomplete resource.

For example, with Unified Mode enabled, this code from the dhcp cookbook is designed to create and edit a shared dhcp_subnet resource, but it won’t work as expected:

# 'edit_resource' results in an incomplete subresource
sr = edit_resource(:dhcp_subnet, "#{new_resource.name}_sharedsubnet_#{subnet}") do
  owner new_resource.owner
  group new_resource.group
  mode new_resource.mode

  ip_version new_resource.ip_version
  conf_dir new_resource.conf_dir
  shared_network true
end

properties.each do |property, value|
  sr.send(property, value)
end

To correct custom resources that change sub-resources during their declaration, you can:

• Apply properties in the code block (preferred)
• Run the resource explicitly (not preferred)

Apply properties in the code block

This pattern declares the sub-resource in one code block and then changes it in the next code block. This is the preferred pattern in Unified Mode because all resources execute in order at compile time.

dhcp_subnet "#{new_resource.name}_sharedsubnet_#{subnet}" do
  owner new_resource.owner
  group new_resource.group
  mode new_resource.mode

  ip_version new_resource.ip_version
  conf_dir new_resource.conf_dir
  shared_network true

  properties.each do |property, value|
    send(property, value)
  end
end

Run the resource explicitly

Another solution is to continue saving the resource as a variable, declare action :nothing within the codeblock, and then explicitly run the action in another code block.

The pattern of saving a resource as a variable and then forcing it to run at compile time with an explicit run_action works as it has in the past, but it’s not a preferred pattern. Unified mode forces resource execution to compile time by default, which makes this pattern redundant.

sr = edit_resource(:dhcp_subnet, "#{new_resource.name}_sharedsubnet_#{subnet}") do
  owner new_resource.owner
  group new_resource.group
  mode new_resource.mode

  ip_version new_resource.ip_version
  conf_dir new_resource.conf_dir
  shared_network true

  action :nothing
end

properties.each do |property, value|
  sr.send(property, value)
end

# Run the action explicitly
sr.run_action(:create)