macos_power_management Resource
Use the macos_power_management resource to set the power settings of a kiosk-style device when you need it always-on
New in Chef Desktop 1.0.
Syntax
The full syntax for all of the properties that are available to the macos_power_management resource is:
macos_power_management 'name' do
computer_sleep_time String # default value: "never"
disk_sleep_time String # default value: "never"
display_sleep_time String # default value: "never"
action Symbol # defaults to :set if not specified
end
where:
macos_power_management
is the resource.name
is the name given to the resource block.action
identifies which steps Chef Infra Client will take to bring the node into the desired state.computer_sleep_time
,disk_sleep_time
, anddisplay_sleep_time
are the properties available to this resource.
Actions
The macos_power_management resource has the following actions:
:nothing
- This resource block doesn’t act unless notified by another resource to take action. Once notified, this resource block either runs immediately or is queued up to run at the end of a Chef Infra Client run.
:set
- This action sets the policy as defined in its properties.
Properties
The macos_power_management resource has the following properties:
computer_sleep_time
- Ruby Type: String | Default Value:
never
A time value between 1-60 minutes or “never” to use to set the computer to sleep after. Defaults to never
disk_sleep_time
- Ruby Type: String | Default Value:
never
A time value between 1-60 minutes or “never” to use to set the hard disk to sleep after. Defaults to never
display_sleep_time
- Ruby Type: String | Default Value:
never
A time value between 1-60 minutes or “never” to use to set the display to sleep after. Defaults to never
Common Resource Functionality
Chef resources include common properties, notifications, and resource guards.
Common Properties
The following properties are common to every resource:
compile_time
Ruby Type: true, false | Default Value:
false
Control the phase during which the resource is run on the node. Set to true to run while the resource collection is being built (the
compile phase
). Set to false to run while Chef Infra Client is configuring the node (theconverge phase
).ignore_failure
Ruby Type: true, false, :quiet | Default Value:
false
Continue running a recipe if a resource fails for any reason.
:quiet
won’t display the full stack trace and the recipe will continue to run if a resource fails.retries
Ruby Type: Integer | Default Value:
0
The number of attempts to catch exceptions and retry the resource.
retry_delay
Ruby Type: Integer | Default Value:
2
The delay in seconds between retry attempts.
sensitive
Ruby Type: true, false | Default Value:
false
Ensure that sensitive resource data isn’t logged by Chef Infra Client.
Notifications
notifies
Ruby Type: Symbol, 'Chef::Resource[String]'
A resource may notify another resource to take action when its state changes. Specify a
'resource[name]'
, the:action
that resource should take, and then the:timer
for that action. A resource may notify more than one resource; use anotifies
statement for each resource to be notified.If the referenced resource doesn’t exist, an error is raised. In contrast,
subscribes
won’t fail if the source resource isn’t found.
A timer specifies the point during a Chef Infra Client run at which a notification is run. The following timers are available:
:before
Specifies that the action on a notified resource should be run before processing the resource block in which the notification is located.
:delayed
Default. Specifies that a notification should be queued up, and then executed at the end of a Chef Infra Client run.
:immediate
,:immediately
Specifies that a notification should be run immediately, for each resource notified.
The syntax for notifies
is:
notifies :action, 'resource[name]', :timer
subscribes
Ruby Type: Symbol, 'Chef::Resource[String]'
A resource may listen to another resource, and then take action if the
state of the resource being listened to changes. Specify a
'resource[name]'
, the :action
to be taken, and then the :timer
for
that action.
Note that subscribes
doesn’t apply the specified action to the
resource that it listens to - for example:
file '/etc/nginx/ssl/example.crt' do
mode '0600'
owner 'root'
end
service 'nginx' do
subscribes :reload, 'file[/etc/nginx/ssl/example.crt]', :immediately
end
In this case the subscribes
property reloads the nginx
service
whenever its certificate file, located under
/etc/nginx/ssl/example.crt
, is updated. subscribes
doesn’t make any
changes to the certificate file itself, it merely listens for a change
to the file, and executes the :reload
action for its resource (in this
example nginx
) when a change is detected.
If the other resource doesn’t exist, the subscription won’t raise an
error. Contrast this with the stricter semantics of notifies
, which
will raise an error if the other resource doesn’t exist.
A timer specifies the point during a Chef Infra Client run at which a notification is run. The following timers are available:
:before
Specifies that the action on a notified resource should be run before processing the resource block in which the notification is located.
:delayed
Default. Specifies that a notification should be queued up, and then executed at the end of a Chef Infra Client run.
:immediate
,:immediately
Specifies that a notification should be run immediately, for each resource notified.
The syntax for subscribes
is:
subscribes :action, 'resource[name]', :timer
Guards
A guard property can be used to evaluate the state of a node during the execution phase of a Chef Infra Client run. Based on the results of this evaluation, a guard property is then used to tell Chef Infra Client if it should continue executing a resource. A guard property accepts either a string value or a Ruby block value:
- A string is executed as a shell command. If the command returns
0
, the guard is applied. If the command returns any other value, then the guard property isn’t applied. String guards in a powershell_script run Windows PowerShell commands and may returntrue
in addition to0
. - A block is executed as Ruby code that must return either
true
orfalse
. If the block returnstrue
, the guard property is applied. If the block returnsfalse
, the guard property isn’t applied.
A guard property is useful for ensuring that a resource is idempotent by allowing that resource to test for the desired state as it’s being executed, and then if the desired state is present, for Chef Infra Client to don’thing.
PropertiesThe following properties can be used to define a guard that’s evaluated during the execution phase of a Chef Infra Client run:
not_if
Prevent a resource from executing when the condition returns
true
.only_if
Allow a resource to execute only if the condition returns
true
.
Examples
The following examples demonstrate various approaches for using the macos_power_management resource in recipes:
Configure Power Management settings:
macos_power_management 'Set the Device to a defined power level' do
computer_sleep_time 'never'
display_sleep_time 'never'
disk_sleep_time 'never'
action :set
end